• Quick View
    (0)

    Push once to turn on, push again to turn off, push again to turn the other side on, one last push and it’s off again! It’s basically a push-button toggle switch that connects and disconnects.

    Mini On/Off Push-Button Switch

    NPR 20.00
  • Quick View
    (0)

    The SIM800A Quad-Band GSM/GPRS Module with RS232 Interface is a complete Quad-band GSM/GPRS solution in an LGA(Land grid array) type which can be embedded in the customer applications. SIM800A support Quad-band 850/900/1800/1900 MHz, it can transmit Voice, SMS and data information with low power consumption.

    With a tiny size, it can fit into slim and compact demands of custom design. Featuring and Embedded AT, it allows total cost savings and fast time-to-market for customer applications.

    The SIM800A modem has a SIM800A GSM chip and RS232 interface while enables easy connection with the computer or laptop using the USB to the Serial connector or to the micro-controller using the RS232 to TTL converter. Once you connect the SIM800A modem using the USB to RS232 connector, you need to find the correct COM port from the Device Manager of the USB to Serial Adapter.

    Then you can open Putty or any other terminal software and open a connection to that COM port at 9600 baud rate, which is the default baud rate of this modem. Once a serial connection is open through the computer or your micro-controller you can start sending the AT commands. When you send AT commands for example “AT\r” you should receive back a reply from the SIM800A modem saying “OK” or other response depending on the command sent.

    Sim 800A with Antenna

    NPR 3,000.00
  • Quick View
    (0)

    This Grove-125KHz RFID Reader is a module used to read uem4100 RFID card information with two output formats: Uart and Wiegand. It has a sensitivity with maximum 7cm sensing distance. There is also the electronic brick version of this module.

    RFID Sensor 125 KHZ

    NPR 1,200.00
  • Quick View
    (0)

    MQ3 is one of the most commonly used sensors in the MQ sensor series. It is a Metal Oxide Semiconductor (MOS) type of sensor. Metal oxide sensors are also known as Chemiresistors, because sensing is based on the change of resistance of the sensing material when exposed to alcohol.

    Alcohol Level Sensor(MQ3)

    NPR 580.00
  • Quick View
    (0)

    The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). Its fairly simple to use, but requires careful timing to grab data.

    Temperature Humidity Sensor DHT- 11

    NPR 410.00
  • Quick View
    (0)

    Ultrasonic Sensor HC-SR04 is great for all kind of projects that need distance measurements, avoiding obstacles as examples. HC-SR04 provides 2cm-400cm non-contact measurement function, the ranging accuracy can reach to 3mm. The modules include ultrasonic transmitters, receiver and control circuit.

    Ultrasonic module distance sensor-HC-SR04

    NPR 440.00
  • Quick View
    (0)

    The Arduino Pro Mini is a microcontroller board based on the ATmega328P. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, an on-board resonator, a reset button, and holes for mounting pin headers.

    Arduino Pro Mini Kit

    NPR 5,000.00
  • Quick View
    (0)

    Piezo buzzers are simple devices that can generate basic beeps and tones. They work by using a piezo crystal, a special material that changes shape when voltage is applied to it. If the crystal pushes against a diaphragm, like a tiny speaker cone, it can generate a pressure wave which the human ear picks up as sound.

    Pizeo Buzzer

    NPR 90.00
  • Quick View
    (0)

    At the heart of all piezo-type buzzers is the piezoelectric element. The piezoelectric element is composed of a piezoelectric ceramic and a metal plate held together with adhesive. Both sides of the piezoelectric ceramic plate contain an electrode for electrical conduction.

    Pizeo Buzzer Plate

    NPR 40.00
  • -23%
    Quick View
    (0)

    A soldering iron is a hand tool used in soldering. It supplies heat to melt solder so that it can flow into the joint between two workpieces. A soldering iron is composed of a heated metal tip and an insulated handle.

    Soldering kit

    NPR 1,550.00
  • Quick View
    (0)

    Raspberry pi 4 kit includes:

    – Raspberry pi 4 (8GB)
    – compatible power adapter
    – 32GB SD Card
    – Genuine Pi case
    -Ethernet cable
    -Micro HDMI to HDMI cable
    -heat sink
    – SD card Adapter

    Raspberry Pi 4 (8GB) kit

    NPR 24,000.00
  • Quick View
    (0)

    Cool and handy RFID Keychain. Easy to use and easy to take around.

    This is a blank 125 kHz RFID Keychain fob – often used for electronic locks or customer identification but also found in other systems where a small and easy to carry tag is desired. The tag contains a NXP S50 chip and an antenna, and is passively powered by the reader/writer when placed a couple inches away.

    RFID Key Chain

    NPR 60.00
  • Quick View
    (0)

    MQ4 Methane Gas Sensor detects the concentration of methane gas in the air and ouputs its reading as an analog voltage. The concentration sensing range of 300 ppm to 10,000 ppm is suitable for leak detection. For example, the sensor could detect if someone left a gas stove on but not lit.

    Methane / LPG Sensor (MQ4)

    NPR 550.00
  • Quick View
    (0)

    DC 3V 450mA Micro 370 Air Pump / Fishing Pump / Oxygen Pump

    DC 3V 450mA Micro 370 Air Pump / Fishing Pump / Oxygen Pump

    NPR 600.00
  • Quick View
    (0)

    The Arduino MEGA 2560 is designed for projects that require more I/O lines, more sketch memory and more RAM. With 54 digital I/O pins, 16 analog inputs and a larger space for your sketch it is the recommended board for 3D printers and robotics projects.

    Arduino Mega Starter Kit

    NPR 9,500.00
  • Quick View
    (0)

    64 Pin DIP IC Socket Base Adaptor.
    QUICK OVERVIEW 64 pins. JDEC compliant. Molded notch for proper orientation. Easy to insert and remove ICs. Features: 64 pins. JDEC compliant. Molded notch for proper orientation. Easy to insert and remove ICs. Package Included: 1 x 64 Pin DIP IC Socket Base Adaptor(5 pcs).

    64 Pin DIP IC Socket Base Adaptor

    NPR 50.00