-
-
Arduino Uno/Mega USB Cable
NPR 200.00Use it to connect Arduino Uno, Arduino Mega 2560, Arduino 101 or any board with the USB female A port of your computer.
USB cable type A/B Standard USB 2.0 cable. -
Power Supply for Arduino (9V 1A)
NPR 300.00-
Input: 100~240V, 50/60Hz
-
Output: 9V,1A
-
Works with most devices that use a 9V adaptor and less than 1A of power
-
Power Supply for Arduino
-
-
Arduino Uno Casing (Transparent Box)
NPR 300.00Protect your Arduino UNO R3 with the transparent and stylish casing.
-
Arduino Breadboard Shield
NPR 450.00Works with the Uno! This prototyping shield is the best out there (well, we think so, at least). It works with UNO, NG, Diecimila and Duemilanove Arduinos.
-
Arduino Sensor Shield
NPR 500.00Arduino Sensor Shield is a board used to connect sensors, servos, LCD with the Arduino Board without the requirement of soldering. Using Arduino Board separately you’ll find a few of 5V and GND connections. Arduino Sensor Shield gives you the ability of dedicated one 5V and GND connection for every Arduino signal pin.
-
Arduino Lilypad
NPR 600.00Microcontroller
ATmega168 or ATmega328V
Operating Voltage
2.7-5.5 V
Input Voltage
2.7-5.5 V
Digital I/O Pins
14
PWM Channels
6
Analog Input Channels
6
DC Current per I/O Pin
40 mA
Flash Memory
16 KB (of which 2 KB used by bootloader)
SRAM
1 KB
EEPROM
512 bytes
Clock Speed
8 MHz
-
4- Channel Arduino Relay Shield
NPR 650.00This relay module allows you to combine the processing power of the Arduino to devices that use higher current and voltage. It does so by providing four relays that are rated for 10A at 125VAC.
There are four relays that each provide dry contact outputs. That is to say that each relay provides a common (COM) , normally open (NO) and a normally closed (NC) terminal.
-
Arduino Voice Record Sound Module ISD1820 with Loudspeaker
NPR 700.00Specification:
The main chip: ISD1820
Size: 38mm * 42.5mm
Working voltage: DC 3 ~ 5V
Loudspeaker: 8Ω, 0.5W.
Features:
1.An easy to use 10 seconds of voice recording
2.High-quality, natural voice restored
3.Can be used as propaganda module
4.With looping, jog playback, single-pass play function
5.Available single-chip control
6.This module can directly drive a small speaker 8 ohm 0.5WPower supply :3-5V, which can be accessed pin power; Audio recording control mode: the key to control or microcontroller, IO has drawn the line of control; Buttons control audio recording method of operation: REC button: record button, you can press and hold the recording, release the button to stop recording; RLAYE key: trigger mode playback, press will play this whole speech; PLAYL key: jog mode playback, press and hold until playback, release to stop playback; RPL Jumper: loop mode control, loop playback; FT Jumper: direct control, microphone voice through the speaker can playback;
-
Arduino L293D Motor Driver Shield
NPR 700.00The Arduino Motor Shield allows you to easily control motor direction and speed using an Arduino. By allowing you to simply address Arduino pins, it makes it very simple to incorporate a motor into your project. It also allows you to be able to power a motor with a separate power supply of up to 12v.
-
VGA OV7670 Camera Module Lens for Arduino
NPR 800.00Feature:
High sensitivity for low-light operation.
Low operating voltage for embedded application.
Standard SCCB interface compatible with I2C interface.
Raw RGB, RGB (GRB4:2:2, RGB565/555/444),YUV(4:2:2) and YCbCr(4:2:2)output format.More Features:
Support VGA, CIF and from CIF to 40 x 30 format.
Vario Pixel method for sub-sampling.
Auto Image Control: AEC, AGC, AWB, ABF, ABLC.
Image Quality Control: Color saturation, hue, gamma, sharpness and anti-blooming.
ISP includes noise reduction and defect correction.
Support image scaling.
Lens shading correction.
Flicker 50/60Hz auto detection.
Color saturation level auto adjust.
Edge enhancement level auto adjust.
De-noise level auto adjust. -
Arduino Pro Mini
NPR 899.00Microcontroller:ATmega328
Operating Voltage:3.3V or 5V (depending on model)
Input Voltage:3.35 -12 V (3.3V model)or 5 – 12 V (5V model)
Digital I/O Pins:14 (of which 6 provide PWM output)
Analog Input Pins:6
DC Current per I/O Pin:40 mA
Flash Memory32 kB (of which 0.5 kB used by bootloader)
SRAM:2 kB
EEPROM:1 kB
Clock Speed:8 MHz (3.3V model) or 16 MHz (5V model)
-
Solenoid Valve (0.5″ 12V)
NPR 1,350.00A solenoid valve is an electromechanically operated valve. The valve is controlled by an electric current through a solenoid: in the case of a two-port valve the flow is switched on or off; in the case of a three-port valve, the outflow is switched between the two outlet ports. Solenoid valves are the most frequently used control elements in fluidics. Their tasks are to shut off, release, dose, distribute or mix fluids. They are found in many application areas. Solenoids offer fast and safe switching, high reliability, long service life, good medium compatibility of the materials used, low control power and compact design.
-
Monster Motor Sheild (for Arduino) VNH2SP30 30A
NPR 1,399.00This is essentially a ramped up version of our Ardumoto motor driver shield. For this monster shield we’ve replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. We’ve also beefed up the support circuitry so this board is capable of driving a pair of high-current motors!
-
Proto Shield for Arduino kit (Adafruit)
NPR 1,500.00This prototyping shield is the best out there (well, we think so, at least), and now is even better with Version R3 – updated for the most compatibility with just about all the Arduinos! It works with UNO, Mega, Leonardo, NG, Diecimila, Duemilanove, and compatible Arduinos. Yun’s and Arduino Ethernets have a chunky Ethernet jack that gets in the way of stacking, you can use the stacking headers included and it will work, just doesn’t sit nice and flat.
BreadFruit Electronics | | Buy latest Arduino, Sensors, Raspberry Pi, ICs, Resistors and other electronic components in Nepal
