-
This module is a soil moisture detector sensor module + it has corrosion resistance probe which are compatible with the Arduino. This soil moisture sensor can read the amount of the moisture present in the surrounding soil.This soil moisture arduino compatible sensor uses the two probe to pass the current through the soil, as if in the soil more water is present than that soil will conduct the electricity more easily like less resistance will be offered and if the soil is dry than that soil will offer more resistance and soil conduct electricity will be poor. This Moisture Sensor can be used to detect the moisture of soil or judge if there is water around the sensor, let the plants in your garden reach out for human help. They can be very to use, just insert it into the soil and then read it. With help of this sensor, it will be realizable to make the plant remind you. if there is requirement of water or not. This module requires input supply voltage of 3.3 – 5VDC and its working current is less than 20mA. This soil humidity detection module includes a potentiometer and soil moisture thresholds.
Soil Moisture Sensor and Soil Detector Module Soil Moisture Test Soil Moisture Test Corrosion Resistance Probe for Arduino
NPR 750.00 -
Technical specification
Supply: 5 V
Power consumption: 0.4 to 1.0 mA
Min. Ee irradiation: 0.35 mW/m2 typ.
Angle of detection: 90
Temperature range: -25 C to +85 CTSOP1838 IR Receiver
NPR 40.00 -
Photo resistors, also known as light dependent resistors (LDR), are light sensitive devices most often used to indicate the presence or absence of light, or to measure the light intensity.
LDR Sensor
NPR 25.00 -
The NEO-6 module series brings the high performance to the miniature NEO form factor. It has been designed with low power consumption and low costs in mind. Intelligent power management is a breakthrough for low-power applications.
It can track up to 22 satellites on 50 channels and achieves the industry’s highest level of sensitivity i.e. -161 dB tracking, while consuming only 45mA supply current. The u-blox 6 positioning engine also boasts a Time-To-First-Fix (TTFF) of under 1 second.
Neo-6M-0-001 V2 with ceramic antenna (GPS Module)
NPR 2,200.00 -
The MAX30102 is an integrated pulse oximetry and heart-rate monitor biosensor module. It includes internal LEDs, photodetectors, optical elements, and low-noise electronics with ambient light rejection. The MAX30102 provides a complete system solution to ease the design-in process for mobile and wearable devices.The MAX30102 operates on a single 1.8V power supply and a separate 5.0V power supply for the internal LEDs. Communication is through a standard I2C-compatible interface. The module can be shut down through software with zero standby current, allowing the power rails to remain powered at all times.
MAX30102 stop and heart beat sensor
NPR 600.00 -
The TCRT5000 are reflective sensors which include an infrared emitter and phototransistor in a leaded package which blocks visible light. The package includes two mounting clips.TCRT5000 sensor works with the general infrared sensor, like a sense of a TCRT5000 has an infrared emission tube and an infrared receiver tube.TCRT5000 Reflective Infrared Optical Sensor
NPR 75.00 -
MQ3 is one of the most commonly used sensors in the MQ sensor series. It is a Metal Oxide Semiconductor (MOS) type of sensor. Metal oxide sensors are also known as Chemiresistors, because sensing is based on the change of resistance of the sensing material when exposed to alcohol.
Alcohol Level Sensor(MQ3)
NPR 580.00 -
-
The TCS3200 programmable color light-to-frequency converter combines configurable silicon photodiodes and a current-to-frequency converter on a single monolithic CMOS integrated circuit. The output is a square wave (50% duty cycle) with frequency directly proportional to light intensity (irradiance). The TCS3200 reads an 8×8 array of photodiodes.
TCS 3200 (Color Sensor)
NPR 680.00 -
This Liquefied Petroleum Gas (LPG) sensor is suitable for sensing LPG (composed of mostly propane and butane) concentrations in the air. It can detect gas concentrations anywhere from 200 to 10000ppm. This sensor has a high sensitivity and fast response time. The sensor’s output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC.
LPG Gas Sensor (MQ6)
NPR 550.00 -
Thyristor is a solid-state semiconductor device with four layers of alternating N and P-type material. It acts exclusively as a bistable switch, conducting when the gate receives a current trigger, and continuing to conduct while the voltage across the device is not reversed (forward-biased). It is one of the several controllable semi conductor devices that can act either like a switch, rectifier or as a voltage regulator.
Thyristor / Thermistor
NPR 30.00 -
This Grove-125KHz RFID Reader is a module used to read uem4100 RFID card information with two output formats: Uart and Wiegand. It has a sensitivity with maximum 7cm sensing distance. There is also the electronic brick version of this module.
RFID Sensor 125 KHZ
NPR 1,200.00 -
A passive infrared sensor (PIR sensor) is an electronic sensor that measures infrared (IR) light radiating from objects in its field of view. They are most often used in PIR-based motion detectors.
For most of our Arduino projects that need to detect when a person has left or entered the area, or has approached, HC-SR501 PIR sensors are a great choice. They are low power and low cost, pretty rugged, have a wide lens range, easy to interface with and are insanely popular among hobbyists.
HC-SR501 PIR sensor has three output pins VCC, Output and Ground as shown in the diagram below. It has a built-in voltage regulator so it can be powered by any DC voltage from 4.5 to 12 volts, typically 5V is used. Other than this, there are a couple options you have with your PIR.
PIR Sensor HC-SR501
NPR 250.00 -
-7%
The sensor contains a accelerometer and a gyro in a single chip. It is very accurate, as it contains 16-bits analog to digital conversion hardware for each channel.
MPU6050 sensor module is complete 6-axis Motion Tracking Device. It combines 3-axis Gyroscope, 3-axis Accelerometer and Digital Motion Processor all in small package. Also, it has additional feature of on-chip Temperature sensor. It has I2C bus interface to communicate with the microcontrollers.
Accelerometer + Gyro (MPU 6050)
NPR 700.00 -
The emitter is an IR LED and the detector is an IR photodiode. The IR phototdiode is sensitive to the IR light emitted by an IR LED. The photo-diode’s resistance and output voltage change in proportion to the IR light received. This is the underlying working principle of the IR sensor.
IR Sensor(Photodiode)
NPR 19.00 -
This gas sensor for monitoring indoor air qualit. it is suitable for sensing NH3, NOx, alcohol, Benzene, smoke and CO2 in the air. The MQ-135 can detect NH3 and Alcohol gas concentrations anywhere from 10-300ppm and Benzene from 10-1000ppm. This sensor has a high sensitivity and fast response time. The sensitivity of the sensor can be adjusted by potentiometer.
Gas Sensor (MQ135)
NPR 550.00
BreadFruit Electronics | | Buy latest Arduino, Sensors, Raspberry Pi, ICs, Resistors and other electronic components in Nepal
