• (0)

    LDR Sensor

    NPR 25.00

    Photo resistors, also known as light dependent resistors (LDR), are light sensitive devices most often used to indicate the presence or absence of light, or to measure the light intensity.

  • (0)

    Neo-6M-0-001 V2 with ceramic antenna (GPS Module)

    NPR 2,200.00

    The NEO-6 module series brings the high performance to the miniature NEO form factor. It has been designed with low power consumption and low costs in mind. Intelligent power management is a breakthrough for low-power applications.

    It can track up to 22 satellites on 50 channels and achieves the industry’s highest level of sensitivity i.e. -161 dB tracking, while consuming only 45mA supply current. The u-blox 6 positioning engine also boasts a Time-To-First-Fix (TTFF) of under 1 second.

  • (0)

    MAX30102 stop and heart beat sensor

    NPR 600.00
    The MAX30102 is an integrated pulse oximetry and heart-rate monitor biosensor module. It includes internal LEDs, photodetectors, optical elements, and low-noise electronics with ambient light rejection. The MAX30102 provides a complete system solution to ease the design-in process for mobile and wearable devices.

    The MAX30102 operates on a single 1.8V power supply and a separate 5.0V power supply for the internal LEDs. Communication is through a standard I2C-compatible interface. The module can be shut down through software with zero standby current, allowing the power rails to remain powered at all times.

  • (0)

    Alcohol Level Sensor(MQ3)

    NPR 580.00

    MQ3 is one of the most commonly used sensors in the MQ sensor series. It is a Metal Oxide Semiconductor (MOS) type of sensor. Metal oxide sensors are also known as Chemiresistors, because sensing is based on the change of resistance of the sensing material when exposed to alcohol.

  • (0)

    TCS 3200 (Color Sensor)

    NPR 680.00

    The TCS3200 programmable color light-to-frequency converter combines configurable silicon photodiodes and a current-to-frequency converter on a single monolithic CMOS integrated circuit. The output is a square wave (50% duty cycle) with frequency directly proportional to light intensity (irradiance).  The TCS3200 reads an 8×8 array of photodiodes.

  • (0)

    LPG Gas Sensor (MQ6)

    NPR 550.00

    This Liquefied Petroleum Gas (LPG) sensor is suitable for sensing LPG (composed of mostly propane and butane) concentrations in the air. It can detect gas concentrations anywhere from 200 to 10000ppm. This sensor has a high sensitivity and fast response time. The sensor’s output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC.

  • (0)

    Thyristor / Thermistor

    NPR 30.00

    Thyristor is a solid-state semiconductor device with four layers of alternating N and P-type material. It acts exclusively as a bistable switch, conducting when the gate receives a current trigger, and continuing to conduct while the voltage across the device is not reversed (forward-biased). It is one of the several controllable semi conductor devices that can act either like a switch, rectifier or as a voltage regulator.

  • (0)

    RFID Sensor 125 KHZ

    NPR 1,200.00

    This Grove-125KHz RFID Reader is a module used to read uem4100 RFID card information with two output formats: Uart and Wiegand. It has a sensitivity with maximum 7cm sensing distance. There is also the electronic brick version of this module.

  • (0)

    TSOP1838 IR Receiver

    NPR 40.00

    Technical specification

    Supply: 5 V
    Power consumption: 0.4 to 1.0 mA
    Min. Ee irradiation: 0.35 mW/m2 typ.
    Angle of detection: 90
    Temperature range: -25 C to +85 C

  • (0)

    PIR Sensor HC-SR501

    NPR 250.00

    A passive infrared sensor (PIR sensor) is an electronic sensor that measures infrared (IR) light radiating from objects in its field of view. They are most often used in PIR-based motion detectors.

    For most of our Arduino projects that need to detect when a person has left or entered the area, or has approached, HC-SR501 PIR sensors are a great choice. They are low power and low cost, pretty rugged, have a wide lens range, easy to interface with and are insanely popular among hobbyists.

    HC-SR501 PIR sensor has three output pins VCC, Output and Ground as shown in the diagram below. It has a built-in voltage regulator so it can be powered by any DC voltage from 4.5 to 12 volts, typically 5V is used. Other than this, there are a couple options you have with your PIR. 

  • (0)

    Accelerometer + Gyro (MPU 6050)

    NPR 700.00

    The sensor contains a accelerometer and a gyro in a single chip. It is very accurate, as it contains 16-bits analog to digital conversion hardware for each channel.
    MPU6050 sensor module is complete 6-axis Motion Tracking Device. It combines 3-axis Gyroscope, 3-axis Accelerometer and Digital Motion Processor all in small package. Also, it has additional feature of on-chip Temperature sensor. It has I2C bus interface to communicate with the microcontrollers.

  • (0)

    IR Sensor(Photodiode)

    NPR 19.00

    The emitter is an IR LED and the detector is an IR photodiode. The IR phototdiode is sensitive to the IR light emitted by an IR LED. The photo-diode’s resistance and output voltage change in proportion to the IR light received. This is the underlying working principle of the IR sensor.

  • (0)

    Carbon Monoxide Sensor (MQ7 | MQ-7)

    NPR 550.00
    This is Carbon Monoxide sensor is suitable for sensing CO concentrations in the air. The MQ-7 can detect CO-gas concentrations anywhere from 20 to 2000ppm.This sensor has a high sensitivity and fast response time. The sensor’s output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC.
  • (0)

    RFID Silicon Wristband 125 KHz

    NPR 320.00
  • (0)

    Vibration Sensor Module

    NPR 350.00

    The vibration sensor module based on the vibration sensor SW-420 and Comparator LM393 is used to detect vibrations. The threshold can adjust using an on-board potentiometer. During no vibration, the sensor provides Logic Low and when the vibration is detected, the sensor provides Logic High.