-
-
Prototyping area for soldering connectors, circuitry or sensors.
-
Onboard 3.3v regulator is both a reliable reference voltage and also reliably runs SD cards that require a lot of power to run
-
Works with Arduino UNO, Duemilanove, Diecimila, Leonardo or ADK/Mega R3 or higher. ADK/Mega R2 or lower are not supported.
-
SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card
-
Real time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years
Arduino Data Logger Shield (Micro SD Slot + RTC)
NPR 1,699.00 -
-
-1%
The Uno R3 CH340G ATmega328p Development Board is the low-cost version of the popular Uno R3 Arduino. It is assembled with the CH340 USB to Serial converter chip, instead of using an Atmega16U2 chip.
Arduino UNO R3 Mega328p CH340 Development Board
NPR 1,690.00 -
It is the Chinese clone of the Arduino Mega 2560 and is capable of doing all the functions.
The MEGA 2560 is designed for more complex projects. With 54 digital I/O pins, 16 analog inputs and a larger space for your sketch it is the recommended board for 3D printers and robotics projects. This gives your projects plenty of room and opportunities.The MEGA 2560 is designed for more complex projects. With 54 digital I/O pins, 16 analog inputs and a larger space for your sketch it is the recommended board for 3D printers and robotics projects. This gives your projects plenty of room and opportunities.
Arduino Mega 2560 (Chinese)
NPR 1,550.00 -
The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3.x) orATmega168 (Arduino Nano 2.x). It has more or less the same functionality of the Arduino Duemilanove, but in a different package. It lacks only a DC power jack, and works with a Mini-B USB cable instead of a standard one. The Nano was designed and is being produced by Gravitech.
- • Automatic reset during program download
- • Power OK blue LED
- • Green (TX), red (RX) and orange (L) LED
- • Auto sensing/switching power input
- • Small mini-B USB for programming and serial monitor
- • ICSP header for direct program download
- • Standard 0.1” spacing DIP (breadboard friendly)
- • Manual reset switch
Arduino Nano with cable
NPR 1,535.00 -
This prototyping shield is the best out there (well, we think so, at least), and now is even better with Version R3 – updated for the most compatibility with just about all the Arduinos! It works with UNO, Mega, Leonardo, NG, Diecimila, Duemilanove, and compatible Arduinos. Yun’s and Arduino Ethernets have a chunky Ethernet jack that gets in the way of stacking, you can use the stacking headers included and it will work, just doesn’t sit nice and flat.
Proto Shield for Arduino kit (Adafruit)
NPR 1,500.00 -
An open-source firmware and development kit that helps you to prototype your IOT product within a few Lua script lines.
Open-source, Interactive, Programmable, Low cost, Simple, Smart, WI-FI enabled.
NodeMCU CP2102 (Arduino Like Hardware)
NPR 1,250.00 -
-20%
Item specifics
Supply Voltage:
Driver Shield V2
Condition:
New
is_customized:
Yes
Model Number:
Driver Shield V2
Type:
Driver Shield V2
Application:
Driver Shield V2
Dissipation Power:
Driver Shield V2
Package:
DIP
Operating Temperature:
Driver Shield V216-channel PWM/Servo Shield
NPR 1,120.00 -
NodeMCU is a Firmware on ESP8266. It is ESP-12 and it is basically a System on Chip (SoC). It has Lua based firmware which is used to develop IoT based applications. It is easy to work on this inexpensive SoC and make our device smart.
NodeMCU CH340 (Arduino Like Hardware)
NPR 900.00 -
Microcontroller:ATmega328
Operating Voltage:3.3V or 5V (depending on model)
Input Voltage:3.35 -12 V (3.3V model)or 5 – 12 V (5V model)
Digital I/O Pins:14 (of which 6 provide PWM output)
Analog Input Pins:6
DC Current per I/O Pin:40 mA
Flash Memory32 kB (of which 0.5 kB used by bootloader)
SRAM:2 kB
EEPROM:1 kB
Clock Speed:8 MHz (3.3V model) or 16 MHz (5V model)
Arduino Pro Mini
NPR 899.00 -
Feature:
High sensitivity for low-light operation.
Low operating voltage for embedded application.
Standard SCCB interface compatible with I2C interface.
Raw RGB, RGB (GRB4:2:2, RGB565/555/444),YUV(4:2:2) and YCbCr(4:2:2)output format.More Features:
Support VGA, CIF and from CIF to 40 x 30 format.
Vario Pixel method for sub-sampling.
Auto Image Control: AEC, AGC, AWB, ABF, ABLC.
Image Quality Control: Color saturation, hue, gamma, sharpness and anti-blooming.
ISP includes noise reduction and defect correction.
Support image scaling.
Lens shading correction.
Flicker 50/60Hz auto detection.
Color saturation level auto adjust.
Edge enhancement level auto adjust.
De-noise level auto adjust.VGA OV7670 Camera Module Lens for Arduino
NPR 800.00 -
The Arduino Motor Shield allows you to easily control motor direction and speed using an Arduino. By allowing you to simply address Arduino pins, it makes it very simple to incorporate a motor into your project. It also allows you to be able to power a motor with a separate power supply of up to 12v.
Arduino L293D Motor Driver Shield
NPR 700.00 -
Specification:
The main chip: ISD1820
Size: 38mm * 42.5mm
Working voltage: DC 3 ~ 5V
Loudspeaker: 8Ω, 0.5W.
Features:
1.An easy to use 10 seconds of voice recording
2.High-quality, natural voice restored
3.Can be used as propaganda module
4.With looping, jog playback, single-pass play function
5.Available single-chip control
6.This module can directly drive a small speaker 8 ohm 0.5WPower supply :3-5V, which can be accessed pin power; Audio recording control mode: the key to control or microcontroller, IO has drawn the line of control; Buttons control audio recording method of operation: REC button: record button, you can press and hold the recording, release the button to stop recording; RLAYE key: trigger mode playback, press will play this whole speech; PLAYL key: jog mode playback, press and hold until playback, release to stop playback; RPL Jumper: loop mode control, loop playback; FT Jumper: direct control, microphone voice through the speaker can playback;
Arduino Voice Record Sound Module ISD1820 with Loudspeaker
NPR 700.00 -
This relay module allows you to combine the processing power of the Arduino to devices that use higher current and voltage. It does so by providing four relays that are rated for 10A at 125VAC.
There are four relays that each provide dry contact outputs. That is to say that each relay provides a common (COM) , normally open (NO) and a normally closed (NC) terminal.
4- Channel Arduino Relay Shield
NPR 650.00 -
Microcontroller
ATmega168 or ATmega328V
Operating Voltage
2.7-5.5 V
Input Voltage
2.7-5.5 V
Digital I/O Pins
14
PWM Channels
6
Analog Input Channels
6
DC Current per I/O Pin
40 mA
Flash Memory
16 KB (of which 2 KB used by bootloader)
SRAM
1 KB
EEPROM
512 bytes
Clock Speed
8 MHz
Arduino Lilypad
NPR 600.00 -
Arduino Sensor Shield is a board used to connect sensors, servos, LCD with the Arduino Board without the requirement of soldering. Using Arduino Board separately you’ll find a few of 5V and GND connections. Arduino Sensor Shield gives you the ability of dedicated one 5V and GND connection for every Arduino signal pin.
Arduino Sensor Shield
NPR 500.00 -
Works with the Uno! This prototyping shield is the best out there (well, we think so, at least). It works with UNO, NG, Diecimila and Duemilanove Arduinos.
Arduino Breadboard Shield
NPR 450.00
BreadFruit Electronics | | Buy latest Arduino, Sensors, Raspberry Pi, ICs, Resistors and other electronic components in Nepal
