Best Seller Items
Featured Items
-
Breakable Female Header Pin
NPR 90.00Single row of 40-holes, female header with swiss round machined pins. These units have very high quality round pins to accept and retain machine pin headers much better. Can be cut to size with a pair of wire-cutters. Standard .1″ spacing. We use them extensively in the Olimex development boards. They mate very well with break away headers.
-
Breakable Male Header Pin
NPR 60.00A pin header (or simply header) is a form of electrical connector. It consists of one or more rows of male pins typically spaced 2.54 millimetres (0.1 in) apart, but sometimes 2 millimetres (0.079 in) or 1.27 millimetres (0.05 in) is used as well. The distance between pins is commonly referred as pitch in the electronic community.
-
-
Brushless Motor 1000 KV (A2212/10T)
NPR 1,280.00Motors provide excellent performance, quality, and dependability at an affordable price. Manufactured with high quality bearings and components, brushless motors are some of the smoothest and most powerful in their class.
-
-
Buzzer
NPR 60.0042R 12*8.5mm 3V/5V general
Passive buzzer advantages are:
- Cheap,
- Sound frequency control, you can make a “more than a meter hair Suola Xi ‘efficiency Fruit.
- In some special cases, you can reuse a control and LED port active buzzer
- Process control, Convenient.
-
-
Capacitive Touch Dimmer
NPR 250.00- Hole distance: 16MM
- Aperture: 2.5MM
- Voltage range: 2.4-5V
- Maximum output current: 500MA
- PCB size: L23MM *W20MMThe lamp brightness can be adjusted by requirement, it is very to operate.
It can touch in medium protection, such glass, acrylic, plastic, ceramics and so on, which is very safe.
Wide application of voltage range, you can choose arbitrarily between 2.4V to 4.5V.
Simple applied circuit, less peripheral devices, easy processing, low cost.
Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not affected by the close distance or multi-angle mobile phone interference.
Install: Neednrsquo;t to touch copper foil directly,the dimming can be processed across the acrylic glass(above 3mm) or plastic.
Application: It can control LED module, light and so on.It is available for indoor LED, lighting lamp,DIY automotive lights dimming refit.
Function:Single touch,using the principle of capacitance touch.The default function is switch, dimming, with brightness memories LED touch dimming.It will light slowly when turn on the lights, and become dark slowly when turn off, which effectively avoid the stimulation to eyes.
Dimming mode: Non-polar PWM dimming.
Wiring method: PCB board(VCC,GND) is power input,(LED+, LED-) is connected with the LED lamps of positive and negative level (fingerprint) touch area.
-
Capacitor Box
NPR 150.00This box contains the commonly used ceramic capacitors from picoFarad to nanoFarad
-
Carbon Monoxide Sensor (MQ7 | MQ-7)
NPR 550.00This is Carbon Monoxide sensor is suitable for sensing CO concentrations in the air. The MQ-7 can detect CO-gas concentrations anywhere from 20 to 2000ppm.This sensor has a high sensitivity and fast response time. The sensor’s output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC.
-
-
Common Anode 10 pin 1 bit 7 segment display
NPR 40.00Basically a 7 segment display is a single unit, which can display only 1 digit or 1 character. More digits are displayed by multiplexing single unit 7 segment displays together to form 2 digit display, 3 digit display or 4 digit 7 segment display. Its quiet easy to interface Arduino and 7 Segment display together! -
Conductive Ink Pen
NPR 2,500.00Conductive ink pen helps you to come out with the stroke of a circuit diagram that can conduct electricity, so that if everything will become more wonderful and funny, as you have already been tired of the traditional way about drawing a circuit diagram and want to try some new things. It uses autonomic modulation paint named Buddy, the main ingredient is silver conductive copper mixed powder and nickel powder, it can conduct electricity in two or three minutes after air-dried. With its superior performance, you can do more simple or complex electronic production.
- Note: Shake well before using and you need to maintain a continuous and uniform line when you write, if still not conducting, you’d better to check and find the break by using the multi-meter.
