Best Seller Items
Featured Items
-
This is an USBasp programmer for uploading source codes (Programs that run your electronic devices from your microwave to your quad-copter) to a Micro-controller unit using standard USB port as input, and the 10 on-board pins as output, and the 6 pins ICSP converter, you can use this to program your arduino with ease.
USBASP AVR Programmer(with wire)
NPR 480.00 -
L293D is a dual H-bridge motor driver integrated circuit (IC). Motor drivers act as current amplifiers since they take a low-current control signal and provide a higher-current signal. This higher current signal is used to drive the motors.
L293D H-Bridge Motor Driver
NPR 120.00 -
The MAX7219are compact, serial input/output common-cathode display drivers that interface microprocessors (µPs) to 7-segment numeric LED displays of up to 8 digits, bar-graph displays, or 64 individual LEDs. Included on-chip are a BCD code-B decoder, multiplex scan circuitry, segment and digit drivers, and an 8×8 static RAM that stores each digit.
Maxim MAX7219 CNG
NPR 130.00 -
A passive infrared sensor (PIR sensor) is an electronic sensor that measures infrared (IR) light radiating from objects in its field of view. They are most often used in PIR-based motion detectors.
For most of our Arduino projects that need to detect when a person has left or entered the area, or has approached, HC-SR501 PIR sensors are a great choice. They are low power and low cost, pretty rugged, have a wide lens range, easy to interface with and are insanely popular among hobbyists.
HC-SR501 PIR sensor has three output pins VCC, Output and Ground as shown in the diagram below. It has a built-in voltage regulator so it can be powered by any DC voltage from 4.5 to 12 volts, typically 5V is used. Other than this, there are a couple options you have with your PIR.
PIR Sensor HC-SR501
NPR 250.00 -
-7%
The sensor contains a accelerometer and a gyro in a single chip. It is very accurate, as it contains 16-bits analog to digital conversion hardware for each channel.
MPU6050 sensor module is complete 6-axis Motion Tracking Device. It combines 3-axis Gyroscope, 3-axis Accelerometer and Digital Motion Processor all in small package. Also, it has additional feature of on-chip Temperature sensor. It has I2C bus interface to communicate with the microcontrollers.
Accelerometer + Gyro (MPU 6050)
NPR 700.00 -
The emitter is an IR LED and the detector is an IR photodiode. The IR phototdiode is sensitive to the IR light emitted by an IR LED. The photo-diode’s resistance and output voltage change in proportion to the IR light received. This is the underlying working principle of the IR sensor.
IR Sensor(Photodiode)
NPR 19.00 -
This gas sensor for monitoring indoor air qualit. it is suitable for sensing NH3, NOx, alcohol, Benzene, smoke and CO2 in the air. The MQ-135 can detect NH3 and Alcohol gas concentrations anywhere from 10-300ppm and Benzene from 10-1000ppm. This sensor has a high sensitivity and fast response time. The sensitivity of the sensor can be adjusted by potentiometer.
Gas Sensor (MQ135)
NPR 550.00 -
This is Carbon Monoxide sensor is suitable for sensing CO concentrations in the air. The MQ-7 can detect CO-gas concentrations anywhere from 20 to 2000ppm.This sensor has a high sensitivity and fast response time. The sensor’s output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC.
Carbon Monoxide Sensor (MQ7 | MQ-7)
NPR 550.00 -
This is 60 rpm small metal geared motor which runs on 6V-9V power supply. Highly used for robotics and electronic projects.
60 rpm geared motor
NPR 799.00 -
It consists of a 1602 white character blue backlight LCD. The keypad consists of 5 keys — select, up, right, down and left. To save the digital IO pins, the keypad interface uses only one ADC channel. The key value is read through a 5-stage voltage divider.
LCD 1602 Keypad Shield
NPR 700.00 -
RFID is useful for sensing and identifying tagged people and objects for access control, automation, and a whole range of different applications. This basic RFID tag/card works in the 125kHz RF range and comes with a unique 32-bit ID. It is not re-programmable. This blank, smooth, and mildly flexible RFID tag is ready for your logo (or hand-drawn scribble).
RFID Cards 125 KHz
NPR 50.00 -
RF modules are very popular among the Arduino tinkerers. The 433MHz is used on a wide variety of applications that require wireless control.
Specifications RF 433MHz Receiver
-
Frequency Range: 433.92 MHz
-
Modulation: ASK
-
Input Voltage: 5V
Note: Each unit contains a pair of transmitter and receiver.
RF 433MHz Transmitter & Receiver Module
NPR 280.00 -
-
This capacitive touch sensor module uses the TTP229 integrated circuit, making it easy to add capacitive touch input for projects. It features 16 sensitive touch pads that make an ideal replacement for the traditional keypads.
16 Channel Digital Capacitive Switch Touch Sensor Module
NPR 350.00 -
Remote control
Operating voltage: DC12V (27A/12V battery x1)
Operating Current: 10mA @ 12V
Radiated power: 10mw @ 12V
Modulation mode: ASK (Amplitude Modulation)
Transmitting frequency: 315MHZ (SAW frequency stabilization)
Transmission distance :50-100M (Open field the receiver sensitivity -100dbm)
Encoder types: fixed code
The frequency of this product is 315 mhz.
315MHZ Wireless 4 Channel Key Remote Control Receiver Module
NPR 700.00
