Best Seller Items
Featured Items
-
-
A float switch is a device used to sense the level of liquid within a tank. Products can be used for drinking fountains, water heaters, solar, air conditioners, humidifiers, bathroom equipment, vending machines, etc. This is a mini float switch. Contains no mercury.
Water level sensor (vertical)
NPR 550.00 -
20 Pins Connector Flat Ribbon Cable,2.54mm Pitch
Easily and directly inserted into PCB
Suitable for internal wiring in office equipment, audio and video machines
IDC 20 Pins Rainbow/Gray Color 2.54mm Pitch 48/66/118/128cm Long Flat Bendable Ribbon Jumper Cable Female Connector
NPR 540.00 -
Arduino Sensor Shield is a board used to connect sensors, servos, LCD with the Arduino Board without the requirement of soldering. Using Arduino Board separately you’ll find a few of 5V and GND connections. Arduino Sensor Shield gives you the ability of dedicated one 5V and GND connection for every Arduino signal pin.
Arduino Sensor Shield
NPR 500.00 -
Gas Sensor(MQ5) module is useful for gas leakage detection (in home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol. Due to its high sensitivity and fast response time, measurements can be taken as soon as possible. The sensitivity of the sensor can be adjusted by using the potentiometer.
Gas Sensor(MQ5)
NPR 500.00 -
0.96 inch IIC Serial White OLED Display Module 128X64 (Yellow-Blue, & just Blue)
IIC Serial White OLED Display Module
NPR 500.00 -
A pair of infrared sensor and a 21 keyed remote control.
Infrared Sensor + Remote Control
NPR 500.00 -
This module integrates DHT11 sensor and other required components on a small PCB. The DHT11 sensor includes a resistive-type humidity measurement component, an NTC temperature measurement component and a high-performance 8-bit microcontroller inside, and provides calibrated digital signal output.
Note: The cable is not included in the pack
Temperature Humidity Sensor DHT- 11 Module
NPR 500.00 -
This is a 5V 4-channel relay or four channel relay module interface board, and each channel needs a 15-20mA driver current. It can be used to control various appliances and equipment with large current. It is equiped with high-current relays that work under AC250V 10A or DC30V 10A. It has a standard interface that can be controlled directly by microcontroller.
- Size: 75mm (Length) * 55mm (Width) * 19.3mm (Height)
- Weight: 61g
- PCB Color: Blue
- There are four fixed screw holes at each corner of the board, easy for install and fix. The diameter of the hole is 3.1mm
- High quality Songle relay is used with single pole double throw, a common terminal, a normally open terminal, and a normally closed terminal
- Optical coupling isolation, good anti-interference.
- Closed at low level with indicator on, released at high level with indicator off
- VCC is system power source, and JD_VCC is relay power source. Ship 5V relay by default. Plug jumper cap to use
- The maximum output of the relay: DC 30V/10A, AC 250V/10A
4 Channel Relay Module (5v)
NPR 500.00 -
Features:
-
Brand new and high quality.
-
High conversion rate.
-
High-efficiency output.
-
Excellent weak light effect.
-
Voltage: 6V
-
Power: 1W.
-
Material: Polysilicon.
Mini Solar Cell Solar Panel (6V | 1 W) (110mm * 60mm)
NPR 500.00 -
-
It is an economical and easy to use heating equipment for melting the soldering wire that contains a pointed tip which enables to make fine solder joints.
Solder Iron (220V – 60W)
NPR 500.00 -
2-150mA Mini Handy Light Emitting Diode (LED) Test Box
Mini Handy Light Emitting Diode (LED) Test Box
NPR 500.00 -
DB-2 micro pump motor for water dispenser water priming pump, automotive pump, RC toy experiment pump, aquarium bonsai rockery.
DB2 Dc Pump 8to12v
NPR 500.00 -
Works great with our HX711 Load Cell (Weight) Amplifier board for Arduino.
Build your own electronic scale using the power of Arduino to create added features like recording weight or let “something” happen when a specific weight is reached like opening a relay.
Load Cell Sensor Resistance Strain 20kg
NPR 490.00
