-
TTGO T-Call v1.3 v1.4 ESP32 Wireless Module & SIM800L GPRS Module (with Antenna) is a custom ESP32 (ESP-WROVER-B 8MB PSRAM) based development board with an onboard 2G/GPRS Module SIM800L. The USB Type C pluggable board also has an onboard LiPo Battery Charging Circuit & Connector and is a good choice for building IoT applications.
TTGO T-Call V1.3 ESP32 SIM800L Wireless Module
NPR 11,500.00 -
-30%
-
It is a GX-16 3-Pin Metal Aviation Plug Male and Female Panel Connector. The connector is mostly used to transmit signals or power. This type of connector is used in places where a watertight connection is required, and also in harsh environments.
The connector is ideal for panel mounting and has got separate male and female pins. The cable can be soldered directly on them
GX-16 3 pin
NPR 450.00 -
The SIM800A Quad-Band GSM/GPRS Module with RS232 Interface is a complete Quad-band GSM/GPRS solution in an LGA(Land grid array) type which can be embedded in the customer applications. SIM800A support Quad-band 850/900/1800/1900 MHz, it can transmit Voice, SMS and data information with low power consumption.
With a tiny size, it can fit into slim and compact demands of custom design. Featuring and Embedded AT, it allows total cost savings and fast time-to-market for customer applications.
The SIM800A modem has a SIM800A GSM chip and RS232 interface while enables easy connection with the computer or laptop using the USB to the Serial connector or to the micro-controller using the RS232 to TTL converter. Once you connect the SIM800A modem using the USB to RS232 connector, you need to find the correct COM port from the Device Manager of the USB to Serial Adapter.
Then you can open Putty or any other terminal software and open a connection to that COM port at 9600 baud rate, which is the default baud rate of this modem. Once a serial connection is open through the computer or your micro-controller you can start sending the AT commands. When you send AT commands for example “AT\r” you should receive back a reply from the SIM800A modem saying “OK” or other response depending on the command sent.
Sim 800A with Antenna
NPR 3,000.00 -
HC-05 module is an easy to use Bluetooth SPP (Serial Port Protocol) module, designed for transparent wireless serial connection setup. Serial port Bluetooth module is fully qualified Bluetooth V2.0+EDR (Enhanced Data Rate) 3Mbps Modulation with complete 2.4GHz radio transceiver and baseband.
Bluetooth Module HC-05
NPR 990.00 -
Peltier module (thermoelectric module) is a thermal control module that has both “warming” and “cooling” effects. By passing an electric current through the module, it is possible to change the surface temperature and keep it at the target temperature.
Peltier Thermo-Electric Cooler Module
NPR 2,200.00 -
A level shifter translates logic signals from one level to another. Usually, this shift takes place between 5V and 3.3V, but you can use other voltages as needed, such as 2.5V or 1.8V.
Logic Level Shifter
NPR 100.00 -
Package includes:
1 X Car Chassis
2 X Gear Motor(1:48)
2 X Car Tire
1 X Universal Wheel
1 X Battery Box
1 X All Necessary Screw And Nut2WD DIY Motor Smart Robot Car Chassis Set
NPR 1,450.00 -
The TCA9548A is an I2C multiplexer that allows up to 8 devices with the same I2C address to be hooked up to an MCU or permits up to 8 separate I2C buses to be controlled.
TCA9548A I2C 8 Channel Multiplexer Module
NPR 300.00 -
-
In terms of the form factor, it looks a lot like the nRF24L01 2.4G RF transceiver. This is a serial module with a built-in TCP/IP stack, so you can use it standalone but you will be likely limited. You need a FTDI to connect this module to your computer, and start communicating with it. FTDI is a common name for USB-to-TTL (or serial) converter.
Wireless TXRX – ESP8266 (Serial Wireless Module)
NPR 800.00 -
Nrf24l01L wireless module, uses NRF24l01 IC, works at 2.4Ghz worldwild open ISM band, working data speed up to 2 Mbps, 125 channel can reach multiple channel and jumping channel needs, operation voltage 3.3-3.6V, transmit power up to 20 dBm, then sensitivity can reach -86dbm at 2 Mps high speed.
NRF24L01 Long Range Wireless Module R2 (1.1KM)
NPR 650.00 -
A pair of infrared sensor and a 21 keyed remote control.
Infrared Sensor + Remote Control
NPR 500.00 -
RF modules are very popular among the Arduino tinkerers. The 433MHz is used on a wide variety of applications that require wireless control.
Specifications RF 433MHz Receiver
-
Frequency Range: 433.92 MHz
-
Modulation: ASK
-
Input Voltage: 5V
Note: Each unit contains a pair of transmitter and receiver.
RF 433MHz Transmitter & Receiver Module
NPR 280.00 -
-
The module based on DS1307, The DS1307 serial real-time clock (RTC) is a low-power, full binary-coded decimal (BCD) clock/calendar plus 56 bytes of NV SRAM. Address and data are transferred serially through an I²C, bidirectional bus. The clock/calendar provides seconds, minutes, hours, day, date, month, and year information. The end of the month date is automatically adjusted for months with fewer than 31 days, including corrections for leap year. The clock operates in either the 24-hour or 12-hour format with AM/PM indicator. The DS1307 has a built-in power-sense circuit that detects power failures and automatically switches to the backup supply. Timekeeping operation continues while the part operates from the backup supply.
DS1307 RTC 12C modules
NPR 300.00 -
BreadFruit Electronics | | Buy latest Arduino, Sensors, Raspberry Pi, ICs, Resistors and other electronic components in Nepal
