Best Seller Items
Featured Items
-
IR Infrared Flame Detection Sensor Module
NPR 320.00- Detection angle about 60 degrees, it is sensitive to the flame spectrum.
- Accuracy adjustable
- Operating voltage 3.3V-5V
- With a mounting screw hole
- Comparator chip LM393 ,it is stable.
- Flame detection distance, lighter flame test can be triggered within 0.8m, if the intensity of flame is high , the detection distance will be increased.
-
-
Mini Micro Submersible Water Pump DC 2.5-6V Low Noise Brushless Motor Pump120L/H
NPR 320.00A mini submersible water pump is a centrifugal water pump, which means that it uses a motor to power an impeller that is designed to rotate and push water outwards. The motor is located in a waterproof seal and closely connected to the body of the water pump which it powers.
-
TCA9548A I2C 8 Channel Multiplexer Module
NPR 300.00The TCA9548A is an I2C multiplexer that allows up to 8 devices with the same I2C address to be hooked up to an MCU or permits up to 8 separate I2C buses to be controlled.
-
Arduino Uno Casing (Transparent Box)
NPR 300.00Protect your Arduino UNO R3 with the transparent and stylish casing.
-
Power Supply for Arduino (9V 1A)
NPR 300.00-
Input: 100~240V, 50/60Hz
-
Output: 9V,1A
-
Works with most devices that use a 9V adaptor and less than 1A of power
-
Power Supply for Arduino
-
-
DS1307 RTC 12C modules
NPR 300.00The module based on DS1307, The DS1307 serial real-time clock (RTC) is a low-power, full binary-coded decimal (BCD) clock/calendar plus 56 bytes of NV SRAM. Address and data are transferred serially through an I²C, bidirectional bus. The clock/calendar provides seconds, minutes, hours, day, date, month, and year information. The end of the month date is automatically adjusted for months with fewer than 31 days, including corrections for leap year. The clock operates in either the 24-hour or 12-hour format with AM/PM indicator. The DS1307 has a built-in power-sense circuit that detects power failures and automatically switches to the backup supply. Timekeeping operation continues while the part operates from the backup supply.
-
IR Infrared Obstacle Avoidance Sensor Module
NPR 300.00- IR Infrared Obstacle Avoidance Sensor Module can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, and black and white line tracking and so on
- the module detects the distance 2 ~ 30cm, detection angle 35 °, the distance can detect potential is adjusted.
- Can be used for 3-5V DC power supply modules.
-
-
TTP224 4-Channel Digital Touch Sensor Module Capacitive Touch Switch
NPR 300.00- Simple to Use, Auto Calibration
- Output Status Indicator LED
- Easy to replace mechanical key outputs
-
Solder Iron Stand
NPR 290.00A soldering iron stand is used to keep the hot soldering iron away from you and the work area. A soldering iron stand i made out of metal and comes with a clening sponge to clean the soldering irons tip.
-
RF 433MHz Transmitter & Receiver Module
NPR 280.00RF modules are very popular among the Arduino tinkerers. The 433MHz is used on a wide variety of applications that require wireless control.
Specifications RF 433MHz Receiver
-
Frequency Range: 433.92 MHz
-
Modulation: ASK
-
Input Voltage: 5V
Note: Each unit contains a pair of transmitter and receiver.
-
-
PIR Sensor HC-SR501
NPR 250.00A passive infrared sensor (PIR sensor) is an electronic sensor that measures infrared (IR) light radiating from objects in its field of view. They are most often used in PIR-based motion detectors.
For most of our Arduino projects that need to detect when a person has left or entered the area, or has approached, HC-SR501 PIR sensors are a great choice. They are low power and low cost, pretty rugged, have a wide lens range, easy to interface with and are insanely popular among hobbyists.
HC-SR501 PIR sensor has three output pins VCC, Output and Ground as shown in the diagram below. It has a built-in voltage regulator so it can be powered by any DC voltage from 4.5 to 12 volts, typically 5V is used. Other than this, there are a couple options you have with your PIR.
