• Quick View
    (0)

    TTGO T-Call v1.3 v1.4 ESP32 Wireless Module & SIM800L GPRS Module (with Antenna) is a custom ESP32 (ESP-WROVER-B 8MB PSRAM) based development board with an onboard 2G/GPRS Module SIM800L. The USB Type C pluggable board also has an onboard LiPo Battery Charging Circuit & Connector and is a good choice for building IoT applications.

    TTGO T-Call V1.3 ESP32 SIM800L Wireless Module

    NPR 11,500.00
  • Quick View
    (0)

    SIM808 module is a GSM and GPS two-in-one function module. It is based on the latest GSM/GPS module SIM808 from SIMCOM, supports GSM/GPRS Quad-Band network and combines GPS technology for satellite navigation.

    Sim 808 Module

    NPR 6,980.00
  • Quick View
    (0)

    The SIM800A Quad-Band GSM/GPRS Module with RS232 Interface is a complete Quad-band GSM/GPRS solution in an LGA(Land grid array) type which can be embedded in the customer applications. SIM800A support Quad-band 850/900/1800/1900 MHz, it can transmit Voice, SMS and data information with low power consumption.

    With a tiny size, it can fit into slim and compact demands of custom design. Featuring and Embedded AT, it allows total cost savings and fast time-to-market for customer applications.

    The SIM800A modem has a SIM800A GSM chip and RS232 interface while enables easy connection with the computer or laptop using the USB to the Serial connector or to the micro-controller using the RS232 to TTL converter. Once you connect the SIM800A modem using the USB to RS232 connector, you need to find the correct COM port from the Device Manager of the USB to Serial Adapter.

    Then you can open Putty or any other terminal software and open a connection to that COM port at 9600 baud rate, which is the default baud rate of this modem. Once a serial connection is open through the computer or your micro-controller you can start sending the AT commands. When you send AT commands for example “AT\r” you should receive back a reply from the SIM800A modem saying “OK” or other response depending on the command sent.

    Sim 800A with Antenna

    NPR 3,000.00
  • Quick View
    (0)

    Peltier module (thermoelectric module) is a thermal control module that has both “warming” and “cooling” effects. By passing an electric current through the module, it is possible to change the surface temperature and keep it at the target temperature.

    Peltier Thermo-Electric Cooler Module

    NPR 2,200.00
  • Quick View
  • Quick View
    (0)

    ESP-WROOM-32 ESP32

    NPR 1,940.00
  • Quick View
    (0)
    • This is 3.3V/5V FPM10A Fingerprint Reader Sensor Module
    • Optical Fingerprint Reader Sensor Module For Arduino Locks Serial Communication Interface

    FPM10A Fingerprint Reader Sensor Module (3.3V/5V)

    NPR 1,800.00
  • Quick View
  • Quick View
    (1)

    Using IO port trig trigger location, to the high level signal of at least 10us module automatically sends 8 40khz fang bo, automatic detecting whether a signal return. A signal return, a high level is output through the io port echo, the time duration of the high level is ultrasonic from launch to return. The test distance = (high level time * speed of sound (340m/s)) /2ranging, the measured object area of not less than 0. 5 square meters and the plane as required to smooth, otherwise affect the measurement results.

    JSN-SR40T Ultrasonic Ranging Sensor Module

    NPR 1,800.00
  • Quick View
    (0)

    This GSM Modem can accept any GSM network operator SIM card and act just like a mobile phone with its own unique phone number. Advantage of using this modem will be that you can use its RS232 port to communicate and develop embedded applications. Applications like SMS Control, data transfer, remote control and logging can be developed easily.

    SIM 800L Module

    NPR 1,500.00
  • Quick View
    (0)

    Package includes:
    1 X Car Chassis
    2 X  Gear Motor(1:48)
    2 X  Car Tire
    1 X  Universal Wheel
    1 X Battery Box
    1 X All Necessary Screw And Nut

    2WD DIY Motor Smart Robot Car Chassis Set

    NPR 1,450.00
  • Quick View
    (0)

    This is essentially a ramped up version of our Ardumoto motor driver shield. For this monster shield we’ve replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. We’ve also beefed up the support circuitry so this board is capable of driving a pair of high-current motors!

    Monster Motor Sheild (for Arduino) VNH2SP30 30A

    NPR 1,399.00
  • Quick View
    (0)

    A solenoid valve is an electromechanically operated valve. The valve is controlled by an electric current through a solenoid: in the case of a two-port valve the flow is switched on or off; in the case of a three-port valve, the outflow is switched between the two outlet ports. Solenoid valves are the most frequently used control elements in fluidics. Their tasks are to shut off, release, dose, distribute or mix fluids. They are found in many application areas. Solenoids offer fast and safe switching, high reliability, long service life, good medium compatibility of the materials used, low control power and compact design.

    Solenoid Valve (0.5″ 12V)

    NPR 1,350.00
  • Quick View
    (0)

    HC-05 module is an easy to use Bluetooth SPP (Serial Port Protocol) module, designed for transparent wireless serial connection setup. Serial port Bluetooth module is fully qualified Bluetooth V2.0+EDR (Enhanced Data Rate) 3Mbps Modulation with complete 2.4GHz radio transceiver and baseband.

    Bluetooth Module HC-05

    NPR 990.00
  • Quick View
    (0)
    MAX31865 RTD Platinum Resistance Temperature Detector PT100 to PT1000
    The MAX31865 is an easy-to-use thermistor-to-digital output converter optimized for platinum resistance temperature detectors (RTDs). The external resistor sets the RTD sensitivity, and the high precision Δ- Σ ADC converts the ratio of the RTD resistor to the reference resistor into a digital output. The MAX31865 has overvoltage protection up to ±45V and provides configurable RTD and cable open and short-circuit condition detection.

    MAX31865 RTD Platinum Resistance Temperature Detector Module (PT100 to PT1000)

    NPR 850.00
  • Quick View
    (0)

    In terms of the form factor, it looks a lot like the nRF24L01 2.4G RF transceiver. This is a serial module with a built-in TCP/IP stack, so you can use it standalone but you will be likely limited. You need a FTDI to connect this module to your computer, and start communicating with it. FTDI is a common name for USB-to-TTL (or serial) converter.

    Wireless TXRX – ESP8266 (Serial Wireless Module)

    NPR 800.00