• Quick View
    (0)

    TTGO T-Call v1.3 v1.4 ESP32 Wireless Module & SIM800L GPRS Module (with Antenna) is a custom ESP32 (ESP-WROVER-B 8MB PSRAM) based development board with an onboard 2G/GPRS Module SIM800L. The USB Type C pluggable board also has an onboard LiPo Battery Charging Circuit & Connector and is a good choice for building IoT applications.

    TTGO T-Call V1.3 ESP32 SIM800L Wireless Module

    NPR 11,500.00
  • -30%
    Quick View
    (0)

    Tilt Switch Sensor Module

    NPR 350.00
  • Quick View
    (0)

    It is a GX-16 3-Pin Metal Aviation Plug Male and Female Panel Connector. The connector is mostly used to transmit signals or power. This type of connector is used in places where a watertight connection is required, and also in harsh environments.

    The connector is ideal for panel mounting and has got separate male and female pins. The cable can be soldered directly on them

    GX-16 3 pin

    NPR 450.00
  • Quick View
    (0)

    The SIM800A Quad-Band GSM/GPRS Module with RS232 Interface is a complete Quad-band GSM/GPRS solution in an LGA(Land grid array) type which can be embedded in the customer applications. SIM800A support Quad-band 850/900/1800/1900 MHz, it can transmit Voice, SMS and data information with low power consumption.

    With a tiny size, it can fit into slim and compact demands of custom design. Featuring and Embedded AT, it allows total cost savings and fast time-to-market for customer applications.

    The SIM800A modem has a SIM800A GSM chip and RS232 interface while enables easy connection with the computer or laptop using the USB to the Serial connector or to the micro-controller using the RS232 to TTL converter. Once you connect the SIM800A modem using the USB to RS232 connector, you need to find the correct COM port from the Device Manager of the USB to Serial Adapter.

    Then you can open Putty or any other terminal software and open a connection to that COM port at 9600 baud rate, which is the default baud rate of this modem. Once a serial connection is open through the computer or your micro-controller you can start sending the AT commands. When you send AT commands for example “AT\r” you should receive back a reply from the SIM800A modem saying “OK” or other response depending on the command sent.

    Sim 800A with Antenna

    NPR 3,000.00
  • Quick View
    (0)

    HC-05 module is an easy to use Bluetooth SPP (Serial Port Protocol) module, designed for transparent wireless serial connection setup. Serial port Bluetooth module is fully qualified Bluetooth V2.0+EDR (Enhanced Data Rate) 3Mbps Modulation with complete 2.4GHz radio transceiver and baseband.

    Bluetooth Module HC-05

    NPR 990.00
  • Quick View
    (0)

    Peltier module (thermoelectric module) is a thermal control module that has both “warming” and “cooling” effects. By passing an electric current through the module, it is possible to change the surface temperature and keep it at the target temperature.

    Peltier Thermo-Electric Cooler Module

    NPR 2,200.00
  • Quick View
    (0)

    A level shifter translates logic signals from one level to another. Usually, this shift takes place between 5V and 3.3V, but you can use other voltages as needed, such as 2.5V or 1.8V.

    Logic Level Shifter

    NPR 100.00
  • Quick View
    (0)

    Package includes:
    1 X Car Chassis
    2 X  Gear Motor(1:48)
    2 X  Car Tire
    1 X  Universal Wheel
    1 X Battery Box
    1 X All Necessary Screw And Nut

    2WD DIY Motor Smart Robot Car Chassis Set

    NPR 1,450.00
  • Quick View
    (0)

    The TCA9548A is an I2C multiplexer that allows up to 8 devices with the same I2C address to be hooked up to an MCU or permits up to 8 separate I2C buses to be controlled.

    TCA9548A I2C 8 Channel Multiplexer Module

    NPR 300.00
  • Quick View
  • Quick View
    (0)

    In terms of the form factor, it looks a lot like the nRF24L01 2.4G RF transceiver. This is a serial module with a built-in TCP/IP stack, so you can use it standalone but you will be likely limited. You need a FTDI to connect this module to your computer, and start communicating with it. FTDI is a common name for USB-to-TTL (or serial) converter.

    Wireless TXRX – ESP8266 (Serial Wireless Module)

    NPR 800.00
  • Quick View
    (0)

    Nrf24l01L wireless module, uses NRF24l01 IC, works at 2.4Ghz worldwild open ISM band, working data speed up to 2 Mbps, 125 channel can reach multiple channel and jumping channel needs, operation voltage 3.3-3.6V, transmit power up to 20 dBm, then sensitivity can reach -86dbm at 2 Mps high speed.

    NRF24L01 Long Range Wireless Module R2 (1.1KM)

    NPR 650.00
  • Quick View
    (0)

    A pair of infrared sensor and a 21 keyed remote control.

    Infrared Sensor + Remote Control

    NPR 500.00
  • Quick View
    (0)

    RF modules are very popular among the Arduino tinkerers. The 433MHz is used on a wide variety of applications that require wireless control.

    Specifications RF 433MHz Receiver

    • Frequency Range: 433.92 MHz

    • Modulation: ASK

    • Input Voltage: 5V

    Note: Each unit contains a pair of transmitter and receiver.

    RF 433MHz Transmitter & Receiver Module

    NPR 280.00
  • Quick View
    (0)

    The module based on DS1307, The DS1307 serial real-time clock (RTC) is a low-power, full binary-coded decimal (BCD) clock/calendar plus 56 bytes of NV SRAM. Address and data are transferred serially through an I²C, bidirectional bus. The clock/calendar provides seconds, minutes, hours, day, date, month, and year information. The end of the month date is automatically adjusted for months with fewer than 31 days, including corrections for leap year. The clock operates in either the 24-hour or 12-hour format with AM/PM indicator. The DS1307 has a built-in power-sense circuit that detects power failures and automatically switches to the backup supply. Timekeeping operation continues while the part operates from the backup supply.

    DS1307 RTC 12C modules

    NPR 300.00
  • Quick View
  • Quick View
    (0)

    This capacitive touch sensor module uses the TTP229 integrated circuit, making it easy to add capacitive touch input for projects. It features 16 sensitive touch pads that make an ideal replacement for the traditional keypads.

    16 Channel Digital Capacitive Switch Touch Sensor Module

    NPR 350.00
  • Quick View
    (0)

    This GSM Modem can accept any GSM network operator SIM card and act just like a mobile phone with its own unique phone number. Advantage of using this modem will be that you can use its RS232 port to communicate and develop embedded applications. Applications like SMS Control, data transfer, remote control and logging can be developed easily.

    SIM 800L Module

    NPR 1,500.00
  • Quick View
    (0)

    This is essentially a ramped up version of our Ardumoto motor driver shield. For this monster shield we’ve replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. We’ve also beefed up the support circuitry so this board is capable of driving a pair of high-current motors!

    Monster Motor Sheild (for Arduino) VNH2SP30 30A

    NPR 1,399.00
  • Quick View
    (0)

    SIM808 module is a GSM and GPS two-in-one function module. It is based on the latest GSM/GPS module SIM808 from SIMCOM, supports GSM/GPRS Quad-Band network and combines GPS technology for satellite navigation.

    Sim 808 Module

    NPR 6,980.00
  • Quick View
    (0)

    Remote control

    Operating voltage: DC12V (27A/12V battery x1)

    Operating Current: 10mA @ 12V

    Radiated power: 10mw @ 12V

    Modulation mode: ASK (Amplitude Modulation)

    Transmitting frequency: 315MHZ (SAW frequency stabilization)

    Transmission distance :50-100M (Open field the receiver sensitivity -100dbm)

    Encoder types: fixed code

    The frequency of this product is 315 mhz.

    315MHZ Wireless 4 Channel Key Remote Control Receiver Module

    NPR 700.00
  • -14%
    Quick View
    (0)
    •    IR Infrared Obstacle Avoidance Sensor Module can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, and black and white line tracking and so on
    •          the module detects the distance 2 ~ 30cm, detection angle 35 °, the distance can detect potential is adjusted.
    •          Can be used for 3-5V DC power supply modules.

    IR Infrared Obstacle Avoidance Sensor Module

    NPR 300.00
  • Quick View
    (0)

    Product Features

    •          Working voltage:DC 3.3-5V
    •          Dimension: Approx.4.5(L) x 1.7(H) x 0.9(W)cm
    •          Main chip: LM393, Electret condenser microphone
    •          Package Included: 1 x Sound Detection Sensor Module

    Sound Detection Sensor Module

    NPR 250.00
  • Quick View
    (0)

    4 line screen 1602 Arduino 1602 I2C interface
    The Arduino IIC LCD1602 / I2C interface adapter plate without LCD screen
    1602 screen needs seven IO mouth to drive up.


    i2c LCD 1602/2004 Adapter Plate

    NPR 350.00
  • Quick View
    (0)

    This module integrates DHT11 sensor and other required components on a small PCB.  The DHT11 sensor includes a resistive-type humidity measurement component, an NTC temperature measurement component and a high-performance 8-bit microcontroller inside, and provides calibrated digital signal output.  

    Note: The cable is not included in the pack

    Temperature Humidity Sensor DHT- 11 Module

    NPR 500.00
  • Quick View
    (0)

    Features:

    •          This module uses a professional microphone amplifier IC.
    •          Low noise
    •          Small size
    •          High sensitivity
    •          Fixed gain in 20db
    •          Voltage: 3-5V
    •          OUT output: default output analog signal.

    MAX9812 Microphone Amplifier Module

    NPR 450.00
  • Quick View
    (0)

    LDR sensor module is used to detect the intensity of light. It is associated with both analog output pin and digital output pin labelled as AO and DO respectively on the board. When there is light, the resistance of LDR will become low according to the intensity of light.

    LDR Sensor Module

    NPR 350.00
  • -9%
    Quick View
    (0)

    Lots of robotic projects need a joystick. This module offers an affordable solution
    to that. The Joystick module is similar to analog joysticks found in gamepads. It is made
    by mounting two potentiometers at a 90 degrees angle. The potentiometers are
    connected to a short stick centered by springs.

    Joystick Module

    NPR 400.00
  • Quick View
    (0)

    The Motor Driver Module is based on the popular L298 dual full-bridge driver. What does that mean? It means that, using this module, your gadget could control the speed and direction of two DC motors up to 40V 3A! 

    L298 Motor Driver Module

    NPR 700.00
  • Quick View
    (0)

    TCRT5000 sensors constantly emit infrared infrared emitting diodes, infrared rays emitted when reflected or not reflected but the intensity is not big enough, the infrared receiver has been in the off state, then the output of the module is low, indicating diode remains off state.

    TCRT5000 IR Infrared Line Track Follower Sensor Obstacle Avoidance Module

    NPR 120.00
  • Quick View
    (0)

    This MP3 module is a small and low cost MP3 module with an amplifier output directly to the speaker.

     The module can be used as a stand alone module with attached battery, speaker and push buttons or used in combination with an Arduino UNO or any other with RX/TX capabilities.

    MP3 WAV Player Module (Micro SD)

    NPR 420.00
  • Quick View
    (0)

    Features:

    • Mini DC to DC 12V-24V to 5V 3A
    • Output 1.8V, 2.5V, 3.3V, 5V, 9V, 12V

    Stepdown Power Supply Module (Buck Converter)

    NPR 250.00
  • Quick View
    (0)

    DHT22 capacitive humidity sensing digital temperature and humidity module is one that contains the compound has been calibrated digital signal output of the temperature and humidity sensors. Application of a dedicated digital modules collection technology and the temperature and humidity sensing technology, to ensure that the product has high reliability and excellent long-term stability.

    Temperature Humidity Sensor DHT-22 Module

    NPR 620.00
  • Quick View
    (0)

    The rain sensor module is an easy tool for rain detection. It can be used as a
    switch when raindrop falls through the raining board and also for measuring rainfall
    intensity. The module features, a rain board and the control board that is separate for
    more convenience, power indicator LED and an adjustable sensitivity though a
    potentiometer. The analog output is used in detection of drops in the amount of rainfall.
    Connected to 5V power supply, the LED will turn on when induction board has no rain
    drop, and DO output is high. When dropping a little amount water, DO output is low, the
    switch indicator will turn on. Brush off the water droplets, and when restored to the initial
    state, outputs high level. 

    Raindrops Sensor Module MH-RD

    NPR 350.00
  • Quick View
    (0)

    Big Button Module

    NPR 100.00
  • Quick View
    (0)

    This is one of the simplest mp3 player module for electronics enthusiasts. Simply insert a MicroSD card, power up the board and play any song/audio.

    Supports mp3 format audio files. 

    Connect a speaker and an earphone to the board and enjoy your audio.

    The circuit board has an inbuilt 2W mono amplifier. 

    MP3 Decoder Module

    NPR 550.00
  • Quick View
    (0)

    This is a DIY metal detector kit parts. You need solder it by yourself. 

    Metal Detector Module

    NPR 600.00
  • Quick View
  • Quick View
    (0)
    • Simple to Use, Auto Calibration
    • Output Status Indicator LED
    • Easy to replace mechanical key outputs

    TTP224 4-Channel Digital Touch Sensor Module Capacitive Touch Switch

    NPR 300.00
  • Quick View
    (0)

    1.Advanced Micro Devices, volume: 1.85 * 211cm

    2.Excellent noise suppression in the case is not connected to the input audio, the ear close to the speaker can not hear any noise

    3.Two-channel stereo, 5V power supply can output 3W +3 W power, can directly drive 4 8 small speaker output power, full of energy, good sound quality.

    4.Unique without LC filter Class D digital power board, and can be used directly to the computer’s USB powered.

    5.Dual-panel wiring, properly solve the crosstalk between the ground potential balance and channel wiring.

    6.Ultra-miniature design, can easily be placed in the internal space for a variety of digital products, ultra high zoom efficiency.

    7.All using the machine for the entire board soldering, hand soldering iron welding quality comparable!

    PAM8403 module Super mini digital amplifier board 2 * 3W Class D digital amplifier board efficient 2.5 to 5V USB power

    NPR 140.00
  • Quick View
    (0)
    • This is 3.3V/5V FPM10A Fingerprint Reader Sensor Module
    • Optical Fingerprint Reader Sensor Module For Arduino Locks Serial Communication Interface

    FPM10A Fingerprint Reader Sensor Module (3.3V/5V)

    NPR 1,800.00
  • Quick View
    (0)

    A solenoid valve is an electromechanically operated valve. The valve is controlled by an electric current through a solenoid: in the case of a two-port valve the flow is switched on or off; in the case of a three-port valve, the outflow is switched between the two outlet ports. Solenoid valves are the most frequently used control elements in fluidics. Their tasks are to shut off, release, dose, distribute or mix fluids. They are found in many application areas. Solenoids offer fast and safe switching, high reliability, long service life, good medium compatibility of the materials used, low control power and compact design.

    Solenoid Valve (0.5″ 12V)

    NPR 1,350.00
  • Quick View
    (0)

    This module is based on the I2C light-to-digital converter TSL2561 to transform light intensity to a digital signal. Different from the traditional analog light sensor, this digital module features a selectable light spectrum range due to its dual light-sensitive diodes: infrared and full spectrum.

    You can switch among three detection modes to take your readings. They are infrared mode, full spectrum, and human visible mode. When running under the human visible mode, this sensor will give you readings just close to your eye feelings.

    Digital Light Sensor Module (TSL2561)

    NPR 800.00
  • Quick View
  • Quick View
    (0)
    Case Color: Blue
    Detection range: Voltage: 3v-7v error 0.1v Current :0-2.5A error 0.01A.
    It’s suitable for factories, laboratories and personal use.

    Digital USB Mobile Power Charging Current Voltage Tester Doctor Voltmeter Ammeter

    NPR 400.00
  • Quick View
    (0)
    Voltage: Ac 250V
    Current: 0.5A
    Color: As Shown in Picture
    Material: Stainless steel,Plastic
     
    Package includes:
    1x Keylock Switch
    2x Keys

    12mm Stainless steel electronic key switch

    NPR 120.00
  • Quick View
    (0)

    Micro USB 5V 1A 18650 TP4056 Lithium Battery Charger Module Charging Board With Protection Dual Functions 1A Li-io

    Micro USB 5V 1A Lithium Battery Charger Module (Charging Board With Protection Dual Function)

    NPR 250.00
  • Quick View
    (0)
    • Hole distance: 16MM
    • Aperture: 2.5MM
    • Voltage range: 2.4-5V
    • Maximum output current: 500MA
    • PCB size: L23MM *W20MMThe lamp brightness can be adjusted by requirement, it is very to operate.
      It can touch in medium protection, such glass, acrylic, plastic, ceramics and so on, which is very safe.
      Wide application of voltage range, you can choose arbitrarily between 2.4V to 4.5V.
      Simple applied circuit, less peripheral devices, easy processing, low cost.
      Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not affected by the close distance or multi-angle mobile phone interference.
      Install: Neednrsquo;t to touch copper foil directly,the dimming can be processed across the acrylic glass(above 3mm) or plastic.
      Application: It can control LED module, light and so on.It is available for indoor LED, lighting lamp,DIY automotive lights dimming refit.
      Function:Single touch,using the principle of capacitance touch.The default function is switch, dimming, with brightness memories LED touch dimming.It will light slowly when turn on the lights, and become dark slowly when turn off, which effectively avoid the stimulation to eyes.
      Dimming mode: Non-polar PWM dimming.
      Wiring method: PCB board(VCC,GND) is power input,(LED+, LED-) is connected with the LED lamps of positive and negative level (fingerprint) touch area.

    Capacitive Touch Dimmer

    NPR 250.00