No products
Prices are tax excluded
HC 06 RF Bluetooth Transceiver Slave Module
Product Description: Mainstream CSR Bluetooth chip Bluetooth V2.0 protocol standardsOperating voltage: 3.3 V.The User defined Baud rate 1200240 0480 0960 0192 00384 00576 00115 00384 the User can setSize: 28 mm x 15 mm x 2.35 mm.The Work Current: 20 ~ 30 ma when pairing, 8 ma after paired Note: This isn't a module with pins. You are required to solder on...
Rs. 690.00In StockGlue Gun Stick
Glue Gun Sticks feature a clear, multi-temp, all-purpose adhesive capable of bonding many plastics, wood products, fabric, leather, foam, PVC, polycarbonate, paper, ribbon and aluminum as well as some polyolefins.
Rs. 29.00In StockRaspberry Pi 40 Pin GPIO Extension Board...
These pins are a physical interface between Pi and the outside world. At the simplest level, you can think of them as switches that you can turn on or off (input) or that the Pi can turn on or off (output). Of the 40 pins, 26 are GPIO pins and the others are power or ground pins (plus two ID EEPROM pins which you should not play with unless you know your...
Rs. 999.00Out of stockTilt Switch
The "poor man's" accelerometer! Tilt sensors are switches that can detect basic motion/orientation. The metal tube has a little metal ball that rolls around in it, when its tilted upright, the ball rolls onto the contacts sticking out of end and shorts them together.
Rs. 50.00Out of stockBluetooth Module HC-05
HC-05 module is an easy to use Bluetooth SPP (Serial Port Protocol) module, designed for transparent wireless serial connection setup.Serial port Bluetooth module is fully qualified Bluetooth V2.0+EDR (Enhanced Data Rate) 3Mbps Modulation with complete 2.4GHz radio transceiver and baseband.
Rs. 900.00 Rs. 999.00Reduced price!Out of stockDigital Accelerometer ADXL 345
3-Axis Digital Accelerometer is the key part in projects like orientation detection, gesture detection and Motion detection.
Rs. 1,099.00Out of stockNokia 5110 LCD
The Nokia 5110 is a basic graphic LCD screen for lots of applications. It was originally intended for as a cell phone screen. This one is mounted on an easy to solder PCB.
Rs. 799.00 Rs. 999.00Out of stockRed Basic LED 5mm
This is a very basic 5mm LED with a red lens. It has a typical forward voltage of 2.0V and a rated forward current of 20mA.
Rs. 5.00Out of stockStepdown Power Supply Module (Buck Converter)
Features: Mini DC to DC 12V-24V to 5V 3A Output 1.8V, 2.5V, 3.3V, 5V, 9V, 12V
Rs. 250.00In StockFlight Controllar (CC3D) for Drones
The CC3D is a powerful and affordable flight controller that is very popular to use mainly on miniquad copters due to its small form factor. It has many advanced features that you can use if you add a GPS module, even waypoint based flight,. However, most users don't bother with this for mini quadcopters and just want the basic setup.
Rs. 2,500.00In StockArduino UNO Casing (Acrylic Box)
Protect your Arduino UNO R3 with the transparent and stylish casing.
Rs. 499.00Out of stockDigital Multimeter (DT9205A)
Features: Data Hold Automatic Power Off Large LCD Display Auto Zero Function Single 32 position switch for function and range
Rs. 620.00Out of stockTemperature Humidity Sensor DHT- 11 Module
This module integrates DHT11 sensor and other required components on a small PCB. The DHT11 sensor includes a resistive-type humidity measurement component, an NTC temperature measurement component and a high-performance 8-bit microcontroller inside, and provides calibrated digital signal output. Note: The cable is not included in the pack
Rs. 350.00Out of stockMPU-9250 Nine-Axis (Gyro + Accelerometer +...
MPU-9250 IMU Breakout features the latest 9-axis MEMS sensor from InvenSense. Each of these 9DoF breakouts feature an MPU-9250 with a System in Package (SiP) that combines two chips: the MPU-6500, which contains a 3-axis gyroscope as well as a 3-axis accelerometer, and the AK8963, which features a 3-axis magnetometer.
Rs. 2,500.00Out of stockL293D H-Bridge Motor Driver
L293D is a dual H-bridge motor driver integrated circuit (IC). Motor drivers act as current amplifiers since they take a low-current control signal and provide a higher-current signal. This higher current signal is used to drive the motors.
Rs. 120.00In Stock
Raspberry PI Zero
The Raspberry Pi Zero is half the size of a Model A+, with twice the utility. A tiny Raspberry Pi that’s affordable enough for any project! The version 1.3 was released in May 2016.
Rs. 2,500.00 Rs. 5,000.00Reduced price!In StockArduino Mega 2560 R3 (Italy)
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins , 16 analog inputs, 4 UARTs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Rs. 2,490.00 Rs. 2,560.00Reduced price!In StockArduino Data Logger Shield (Micro SD Slot...
SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD cardReal time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years
Rs. 1,359.20 Rs. 1,699.00 -20%Reduced price!In StockWaterproof ultrasonic sensor
Take your sonar outside - great for all weather robots! The XL-MaxSonar-WRMA1 ignores smaller targets and only reports the range to target with the largest acoustic return. This is our most advanced weather resistant sensor designed for target detection and ranging outdoors or in tank or bin applications.
Rs. 1,099.00 Rs. 1,299.00Out of stockArduino Nano v3
The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3.x) orATmega168 (Arduino Nano 2.x). It has more or less the same functionality of the Arduino Duemilanove.
Rs. 999.00 Rs. 1,399.00Out of stock
Male to Male LQ Small Connector (Jumper Wire)
While many connectors carry power in addition to data, some connectors are used specifically to provide power connections to devices. These vary widely by application and size.
Rs. 7.00Out of stockMale to Female HQ Connector (Jumper Wire)
These are 155mm long jumpers terminated as male to female. Use these to jumper from any male or female header on any board. Multiple jumpers can be installed next to one another on a 0.1" header.
Rs. 10.00In StockDuPont Male to Male Jumper Cables
This product is a DuPont Male to Male Jumper Cables. The cables are to be ordered on the basis of number required. The item here represents a single piece of wire and not the whole bunch.
Rs. 10.00In StockGreen Basic LED 5mm
This is a very basic 5mm LED with a green lens. It has a typical forward voltage of 2.0V and a rated forward current of 20mA.
Rs. 5.00In StockWhite LED
These are very bright LEDs. The LEDs are so bright that it hurts to look directly at them. Features:Standard Size - T1 ¾ 5mmForward Voltage:Min: 3.2VMax: 3.4VMax current 20mA
Rs. 5.00Out of stockLDR Sensor
Photo resistors, also known as light dependent resistors (LDR), are light sensitive devices most often used to indicate the presence or absence of light, or to measure the light intensity.
Rs. 15.00In StockHeat Shrink Tube 2mm
Use it for all sorts of handy projects. Use it to reinforce connections, protect devices, and electrically isolate exposed solder joints. Currently, only available in yellow color.
Rs. 5.00Out of stock
